How Much Does A Leveling Kit Cost?

Are you facing problems in truck balance while carrying a full payload with the product? Usually, any truck or car will have a decent tilt towards the front. If there are potholes or bumps on the road, the entire vehicle will be imbalanced. This is where a leveling kit becomes so important to use. It is a specific tool kit set that brings back the balance of your vehicle. It mostly works on the front wheel allowing your vehicle to attain a better ground clearance. If you’re worried about installing it or how it works, this guide is for you.

How Much does It Cost To Level a Truck?

The main job role of a leveling kit is to balance the car or truck in a uniform properly. It basically works as a ground clearance unit of your car, which allows you to get a proper balance. If you do not have a proper balance on the truck, an uneven road or bumps on the road could disbalance your truck. This is where a leveling kit comes to play. It is used to lift the vehicle at a certain height, making the truck clear any obstruction. The leveling kit comes with multiple parts like strut extensions, coil spring spacers, and torsion bar keys with individual benefits.

The leveling kit helps your truck attain uniform balance even while it is fully loaded or traveling from one place to another. Practically, it is a bit different from the genuine lift kit. It does not increase the overall ground clearance of the product, but this tool allows your truck to attain a proper height. It specifically works in the front of your vehicle to balance out the payload capacity. It makes the vehicle’s overall appearance get enhanced and comes with a subtle change to make it grow better. The overall result for your car is much improved.

How to Install a Leveling Kit?

To install the leveling kit, you’ll need to go through several steps. Start by collecting all the materials together, and then you can set up the leveling kit. Every kit comes with different installation instructions. This is why it is important to go through them for once. To keep yourself safe, you need to have a few handy instruments close to you.

Materials Required:

• Extra nuts
• Floor jack
• PB Blaster
• Torque Wrench
• Ratchet
• Screwdriver
• Pliers
• Hammer

Installing Coil Spring Spacers:

Step 1: The first thing that you will have to do is to block the rear tires. It would help if you parked it with the brakes on.

Step 2: Now you will have to remove your tires slowly, and then you will raise the suspension. Set up the floor jack around the axle and compress the spring slightly.

Step 3: You will not be able to install the spring compressor and then make it tight and secure. Remove the external clips, and your tool is ready.

Installing Strut Extensions

Step 1: Start by blocking out the rear tires again, and then make sure that it is secure. You can now use some hydraulic jacks to secure the wheel and lift the vehicle.

Step 2: Go a bit slow, and you will be able to remove tires that are present. Remove them, and then you will have to place the six studs around the extenders.

Step 3: Now you can remove the sway bar link. Grab the tie rod end fastener, and you will be able to get a great result.

Step 4: You will not have to spot the ball joint and then slowly rotate it to loosen this joint. You can use a mallet to get it out from the knuckle.

Step 5: Once done, the last thing that you will need to do is to remove the lower strut bolt. You can now replace it with the control arm and a new strut.

Installing Torsion Bar Keys

Step 1: The first thing you need to do is take the pressure off the suspension and the torsion bars. You can use torsion bar removal tools.

Step 2: You will now be able to remove the retaining plates that are present over here. Now slowly get the adjusting bolts and make sure that they are changed.

Step 3: The next step is to remove the torsion bar and then take out the old keys. You will be able to easily spot a difference between the new key and the old key.

Step 4: The next thing that you need to do is repeat the same process for the backward tires. Follow every instruction again for the rear tires, and you will be able to install the torsion bar keys easily.

Note: While installing the leveling kits, you may face a few alignment problems. It is thus important to have a look at your wheels before driving off.

How Much Does A Leveling Kit Cost?

The leveling kit installation cost depends on the type of parts you are installing or even the different wheels. However, if you want to install them yourself, you can estimate around $400 to $2000. However, when it comes to getting it done by a professional, you can spend between $800 to $4000.

Different parts of the leveling kit have different manufacturing prices. Also, the prices may differ according to your location and the number of parts present. But you can always choose the ideal one according to your requirements. Consulting with a professional is a must if you want to lift a truck for the first time successfully.

Final Talk

Installing a leveling kit is mandatory when you are traveling with a full payload for a long journey. Also, it may turn out to be essential depending on the road on which you will travel. For the first time, if you are doing it, do deep research about it from your home and contact a professional. However, it is definitely worth having a leveling kit for your car needs.